Digitone II Mods / bug fixes / LFO ONE and HALF
In TRIG MODE ONE, an LFO should run one cycle and then stop. In HALF, it should run half a cycle and then stop. The factory firmware gets both parts wrong. It stops at fixed points of the cycle, and does not count from the start phase. So with SPH moved, the LFO ends early (or, in HALF, late). And when it stops, it jumps to the centre: a square on the filter “turns off” or “jumps back to the middle”.
This mod fixes both, on audio and MIDI tracks. Select your firmware file. Then download a signed image.
Make sure that you can go back to stock before you flash a modified file. The Early Start-up Menu flashes the stock firmware over MIDI. Do this one time with the stock file, before you flash a modified file. Back up your +Drive. No tool here can recover it.
Go to 1.11 from 1.10E. If your unit has OS 1.10D, install the stock OS 1.10E first. Then install OS 1.11, stock or modified. Do not go from 1.10D directly to 1.11.
This mod is at v1.0.1. What changed in each version, newest first.
The table below is the row of this mod in the
compatibility table. dnfw mods matrix generates it.
✓: you can combine the two mods in either order. ✓*: you can combine them in one order only. ✗: you cannot combine them. To see the reason, put the pointer on a cell.
arpmodes | arpplocks | arpscale | bootscreen | degreetranspose | directjump | fxmod | layermidi | lfo4 | lfolength | lfowaves | midiarp | moddest | reloadconfirm | sendloop | songguard | transients | usbprobe | waverider | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
LFO ONE/HALF fix lfolength | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ | — | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ | ✓ |
This mod combines with Arpeggiator SHUF and RAND, Arpeggiator p-locks, Arp offsets in scale, Boot screen, Degree transpose, Direct jump, LFO modulation of the FX, Layering onto MIDI tracks, A fourth LFO, New LFO waveforms, Arpeggiator on MIDI tracks, More modulation destinations, Reload confirm, Send loop, Song guard, FM drum transients, USB SysEx probe (diagnostic) and Waverider, a sixth machine. See the compatibility table.
Factory 1.11 against the fixed firmware, every combination of the values below, on both copies of the LFO code (audio tracks and MIDI tracks).
| What was varied | Values | Cases | Result | Where |
|---|---|---|---|---|
| Trig mode | FREE, TRIG, HOLD, ONE, HALF | 5 | only ONE and HALF change. They follow the TRIG waveform until they stop | emulator |
| Waveform | the 7 stock ones | 7 | ||
| SPH | 0, 32, 64, 96 | 4 | ||
| Speed | + and − | 2 | ||
| Fade | off and on | 2 | ||
| Trigs | one, retrig mid-run, retrig after the stop | 3 | ||
| Totals | every combination | 1680 audio + 1680 MIDI | all pass | |
| Mode change mid-run | ONE/HALF → FREE, HOLD, TRIG | 3 | equal to factory | emulator |
| Start-point arithmetic | every phase × every start point | 6056 | all correct | offline check |
| Start-up | boot from reset, the fix’s code in place, the LFO code run | 1 | clean | emulator |
| Hold | ONE and HALF, square and triangle, audio track | holds the value reached | Digitone II, 2026-10-08 | |
| High SPH | 0 to 120, among them 74, 85, 100 and 120, on an audio track | full length, holds, no click or flip at the end | Digitone II, 2026-10-09 |
Not covered: start points past half a cycle in the emulator. The emulator cannot make them, but the instrument test covers them on audio tracks. Also not covered: MIDI tracks on the instrument. We tested MIDI tracks in the emulator only.
Use a Digitone II OS 1.11 .syx file from Elektron. To combine mods, you can
also use an image that a different page here built (refer to the table above).
or drag it here