On stock firmware, a pattern you cue starts when the playing pattern ends. With this mod, it can
start on the next step. It goes on from where the playing pattern was, as on the Analog Rytm with
DIRECT JUMP. Select your firmware file. Then download a signed image.
Make sure that you can go back to stock before you flash a modified file.
The Early Start-up Menu flashes the stock firmware over MIDI. Do this one time with the stock
file, before you flash a modified file. Back up your +Drive. No tool here can recover it.
Go to 1.11 from 1.10E. If your unit has OS 1.10D, install the stock OS 1.10E
first. Then install OS 1.11, stock or modified. Do not go from 1.10D directly to 1.11.
How to use it
Turn it on. Press [PTN] to open the pattern view, or hold it. Then press [UP].
The title bar shows “Direct Jump ON”. While it is on, [PTN] lights magenta in the
pattern view, as the [TRIG] keys do in PATTERN MUTE mode. [DOWN] turns it off and shows
“Direct Jump OFF”.
Cue a pattern. While the sequencer plays, press [PTN] and a [TRIG] key, as on
stock firmware. The new pattern starts on the next step. If you cue late in a step, it starts one
step later. It goes on from the position of the playing pattern. For example, if A01 is on its step 11 and A02 has 8 steps, A02 goes on from its
step 3.
Chains, songs and MIDI program changes change at the end of the pattern, as on stock firmware, unless one comes between a jump’s cue and the jump. The jump takes the newest cue.
With the switch off, every change is stock’s.
Version and changes
This mod is at v0.1.0.
What changed in each version, newest first.
v0.1.0
First version. In the PTN view, press UP to turn DIRECT JUMP on and DOWN to turn it off. With it on, a pattern you cue with PTN and a TRIG key starts on the next step, from where the playing pattern was.
Combines with
The table below is the row of this mod in the
compatibility table. dnfw mods matrix generates it.
✓: you can combine the two mods in either order. ✓*: you can combine them in one order
only. ✗: you cannot combine them. To see the reason, put the pointer on a cell.
arpmodes
arpplocks
arpscale
bootscreen
degreetranspose
directjump
fxmod
layermidi
lfo4
lfolength
lfowaves
midiarp
moddest
reloadconfirm
sendloop
songguard
transients
usbprobe
waverider
Direct jump directjump
✓
✓
✓
✓
✓
—
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
This mod combines with Arpeggiator SHUF and RAND, Arpeggiator p-locks, Arp offsets in scale, Boot screen, Degree transpose, LFO modulation of the FX, Layering onto MIDI tracks, A fourth LFO, LFO ONE/HALF fix, New LFO waveforms, Arpeggiator on MIDI tracks, More modulation destinations, Reload confirm, Send loop, Song guard, FM drum transients, USB SysEx probe (diagnostic) and Waverider, a sixth machine. See the compatibility table.
1
Your firmware
Use a Digitone II OS 1.11 .syx file from Elektron. To combine mods, you can
also use an image that a different page here built (refer to the table above).
or drag it here
2
What changes
The switch
In the pattern view, [UP] turns DIRECT JUMP on and [DOWN] turns it off. Off by default, so an instrument that has never had it on behaves as stock. The mod takes a cue made with the switch on within about 40 ms. After that, the jump goes ahead even if you turn the switch off
On
A pattern cued in the pattern view while the sequencer plays starts on the next step. At 1x, a cue in the last third of a step starts on the step after. The pattern goes on from the playing pattern’s position, wrapped by its own length. In per-track mode, each track wraps by its own length
Page Loop
The position is the full pattern’s, which the top row of [TRIG] keys shows
LST
A jump cuts the last pass short. Trigs with LST do not play, and trigs with !LST play. A cue too late for the next step lets the old pattern play one more step as its last pass
Stock anyway
Chains, songs, MIDI program changes, and a cue while the sequencer is stopped. One that comes between a jump’s cue and the jump is taken by the jump
Kept
The instrument saves the switch with its settings, as it saves the switches of Reload confirm and Arp offsets in scale. So the switch survives a power cycle without SAVE PROJECT
Writes
—
Not yet tested by the repository owner. On w-winter’s Digitone II, 2026-11-12, the jumps, the
switch, the arp, a heavy load and a power cycle worked. Checked in the emulator, 2026-11-11 and 2026-11-12. Every
cue started on the expected step, at the expected position. The checks included patterns of
different lengths, Page Loop and per-track mode. With the switch off, and for both ways to make a chain, the notes
were the same as stock’s.
3
Build it
The image is rebuilt, re-signed with the key derived from your own file, and
every integrity field is checked again. Nothing downloads unless all of them pass.