The arpeggiator adds each step’s offset in semitones, so an offset can take a note out of
the track’s scale. With this mod, the offsets can count degrees of the scale instead, and
you can mark single steps to stay in semitones. Select your firmware file. Then download a signed image.
Make sure that you can go back to stock before you flash a modified file.
The Early Start-up Menu flashes the stock firmware over MIDI. Do this one time with the stock
file, before you flash a modified file. Back up your +Drive. No tool here can recover it.
Go to 1.11 from 1.10E. If your unit has OS 1.10D, install the stock OS 1.10E
first. Then install OS 1.11, stock or modified. Do not go from 1.10D directly to 1.11.
How to use it
Turn it on. In SETTINGS > PERSONALIZE, set ARP OFS IN SCALE to on. Each
offset now counts degrees of the track’s scale, from its root, as KEYBOARD SETUP sets them.
In C major, E plus 2 plays G, not F#.
Mark a step to move in semitones. Press [ARPEGGIATOR] to open the ARPEGGIATOR menu,
and select a step with [LEFT] or [RIGHT]. On an active step, press [UP]: the step shows a plus,
and its offset counts semitones, for a note outside the scale. [DOWN] removes the mark, and
[DOWN] again mutes the step.
With ARP OFS IN SCALE off, the arpeggiator is stock: every step moves in semitones, and the
menu shows no plus. The marks stay with the sound for when you turn it on again.
Version and changes
This mod is at v0.2.1.
What changed in each version, newest first.
v0.2.1
With ARP OFS IN SCALE off, UP and DOWN in the ARPEGGIATOR menu keep a step's mark. Before, muting a step there removed its mark.
v0.2.0
With ARP OFS IN SCALE on, you can mark an arp step to move in semitones, for a note outside the scale. In the ARPEGGIATOR menu, press UP on an active step: the step shows a plus. Press DOWN to remove the mark, and DOWN again to mute the step.
The sound keeps its marks when you save it, copy it, or copy, paste and clear its arp. With ARP OFS IN SCALE off, every step moves in semitones, as before.
You can now build it on the site, on this page.
v0.1.0
First numbered version.
Not published on the site yet.
Combines with
The table below is the row of this mod in the
compatibility table. dnfw mods matrix generates it.
✓: you can combine the two mods in either order. ✓*: you can combine them in one order
only. ✗: you cannot combine them. To see the reason, put the pointer on a cell.
arpmodes
arpplocks
arpscale
bootscreen
degreetranspose
directjump
fxmod
layermidi
lfo4
lfolength
lfowaves
midiarp
moddest
reloadconfirm
sendloop
songguard
transients
usbprobe
waverider
Arp offsets in scale arpscale
✓
✓
—
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
This mod combines with Arpeggiator SHUF and RAND, Arpeggiator p-locks, Boot screen, Degree transpose, Direct jump, LFO modulation of the FX, Layering onto MIDI tracks, A fourth LFO, LFO ONE/HALF fix, New LFO waveforms, Arpeggiator on MIDI tracks, More modulation destinations, Reload confirm, Send loop, Song guard, FM drum transients, USB SysEx probe (diagnostic) and Waverider, a sixth machine. See the compatibility table.
1
Your firmware
Use a Digitone II OS 1.11 .syx file from Elektron. To combine mods, you can
also use an image that a different page here built (refer to the table above).
or drag it here
2
What changes
The switch
SETTINGS > PERSONALIZE > ARP OFS IN SCALE. Off by default, so a freshly flashed instrument behaves as stock
On
An offset counts degrees of the track’s scale. An offset of 0 plays the held note, even one outside the scale. Other offsets first move a note outside the scale to the nearest note in it. RANGE still adds whole octaves
Marked steps
With the switch on, [UP] on an active step in the ARPEGGIATOR menu marks it, and its offset counts semitones. The marks are saved with the sound, and the menu’s rotate, copy, paste and clear move them with the steps
Off
Stock: every step counts semitones, marked or not, and the menu works and looks as stock
Semitones anyway
SCALE CHROMATIC, and MODE CHORD MEMORY in KEYBOARD SETUP
Kept
The switch is saved with your other PERSONALIZE settings and survives a power cycle, with or without SAVE PROJECT
Writes
—
Confirmed on a Digitone II, 2026-10-14, before marked steps existed. With the
switch on, the arp plays in scale, from trigs and from keys held on the KEYBOARD page. With it off,
the arp plays stock’s notes. The switch stays on after a power cycle.
Marked steps (version 0.2.0) passed on w-winter’s Digitone II, 2026-10-26, on the
current build (arpscale5). With the switch off, [UP] leaves a step’s mark. A sound
sent out and back with the preset manager of Elektron’s Transfer app keeps its marks, and its
marked steps play outside the scale. Stock 1.11 loads a project with marks with no error.
3
Build it
The image is rebuilt, re-signed with the key derived from your own file, and
every integrity field is checked again. Nothing downloads unless all of them pass.